Documentation Conventions - JUNOSe 7.3.x Command Reference Guide

JUNOSe 7.3.x Command Reference Guide

Table 1: Notice Icons
[Contents] [Prev] [Next] [Index] [Cisco] [Reload] JUNOSe 7.3.x Command Reference Guide N to Z > About This Guide > Documentation Conventions Documentation Conventions Table 1 defines notice icons used in this guide.

Icon	Meaning	Description
	Informational note	Indicates important features or instructions.
	Caution	Indicates a situation that might result in loss of data or hardware damage.
	Warning	Alerts you to the risk of personal injury.

Table 2 defines text conventions used in this guide and the syntax conventions used
primarily in the JUNOSe Command Reference Guide. For more information about
command syntax, see JUNOSe System Basics Configuration Guide, Chapter 2,
Command-Line Interface.




 Table 2:  Text and Syntax Conventions 



 Convention
 Description
 Examples


 Text Conventions



 Represents commands and keywords in text.

   Issue the clock source command.
   Specify the keyword exp-msg.



Represents text that the user must type.
host1(config)#traffic class low-loss1


 Represents information as displayed on your terminal's screen.

 host1#show ip ospf 2
 Routing Process OSPF 2 with Router ID 5.5.0.250
 Router is an Area Border Router (ABR)



 

   Emphasizes words. 
   Identifies variables. 
   Identifies chapter, appendix, and book names.



   There are two levels of access, user and privileged.
   clusterId, ipAddress.
   Appendix A, System Specifications.



 Plus sign (+) linking key names

 Indicates that you must press two or more keys simultaneously.

 Press Ctrl+b.


 Syntax Conventions in the Command Reference Guide
 


 Plain typeface

 Represents keywords.

 terminal length


 Italic typeface

 Represents variables.

 mask, accessListName


 | (pipe symbol) 

 Represents a choice to select one keyword or variable to the left or right of this symbol. (The keyword or variable can be either optional or required.)

 diagnostic | line


 [ ] (brackets)

 Represent optional keywords or variables.

 [ internal | external ]


 [ ]* (brackets and asterisk)

 Represent optional keywords or variables that can be entered more than once.

 [ level1 | level2 | l1 ]*


 { } (braces)

 Represent required keywords or variables.

 { permit | deny } { in | out }
{ clusterId | ipAddress }

Convention	Description	Examples
Text Conventions
Represents commands and keywords in text.	Issue the clock source command. Specify the keyword exp-msg.
`Represents text that the user must type.`	`host1(config)#traffic class low-loss1`
`Represents information as displayed on your terminal's screen.`	`host1#show ip ospf 2` `Routing Process OSPF 2 with Router ID 5.5.0.250` `Router is an Area Border Router (ABR)`
Emphasizes words. Identifies variables. Identifies chapter, appendix, and book names.	There are two levels of access, user and privileged. clusterId, ipAddress. Appendix A, System Specifications.
Plus sign (+) linking key names	Indicates that you must press two or more keys simultaneously.	Press Ctrl+b.
Syntax Conventions in the Command Reference Guide
Plain typeface	Represents keywords.	terminal length
Italic typeface	Represents variables.	mask, accessListName
\| (pipe symbol)	Represents a choice to select one keyword or variable to the left or right of this symbol. (The keyword or variable can be either optional or required.)	diagnostic \| line
[ ] (brackets)	Represent optional keywords or variables.	[ internal \| external ]
[ ]* (brackets and asterisk)	Represent optional keywords or variables that can be entered more than once.	[ level1 \| level2 \| l1 ]*
{ } (braces)	Represent required keywords or variables.	{ permit \| deny } { in \| out } { clusterId \| ipAddress }

Using the no Version Versus the default Version of Commands

Most router configuration commands have a no version, which you can use to negate a command (or a portion of it specified by an optional keyword) or restore its default setting. When you use a command without the keyword no, you can reenable a disabled feature or override a default setting. You have the option of using the default keyword whenever the no keyword is also a choice; simply enter the keyword default instead of no.

In most cases, when you execute the default version of a command, it produces the exact results as the no version. There are some commands for which the default version yields a different result than the no version.

Commands for which the default behavior differs from the no behavior are clearly identified in this guide. Unless otherwise specified, therefore, the default command is identical to the no command and is neither documented nor discussed.

The syntax for each no command is described in this guide. Some commands do not have a no version; this is indicated in the individual command descriptions except for the show commands, none of which has a no version.

The CLI can act on no versions of commands when you have entered sufficient information to distinguish the command syntactically, and ignores all subsequent input on that line.

To be compatible with some non-E-series implementations, the no versions of commands accept the same options as the affirmative version of the commands. The CLI ignores the optional input if it has no effect on the command behavior. If using the option changes the behavior of the no version, the individual command entry in this guide describes the difference in behavior.

Deprecated Commands

A command that has been deprecated in a release or in a particular configuration mode returns a notice when you issue the command manually:

NOTICE: This command is obsolete. It may be completely removed from a
subsequent software release.

A preferred alternate command is provided in the notice. If you have a script that uses the deprecated command, the deprecated command is automatically mapped to the preferred command when you run the script. If the deprecated command no longer has a function, then that command has no effect when you run a script containing the command.

We recommend that you use the preferred command when writing new scripts.

Filtering show Commands

You have access to a variety of show commands that display router and protocol information. You can filter the output of a show command by specifying | (the UNIX pipe symbol), one of the following keywords, and either a case-sensitive text string or a regular expression.

begin—Displays output beginning with the first line that contains the text string or regular expression
include—Displays output lines that contain the text string or regular expression and excludes lines that do not contain the text string or regular expression
exclude—Displays output lines that do not contain the text string or regular expression and excludes lines that do contain the text string or regular expression

For a list of regular expressions, see JUNOSe IP Services Configuration Guide, Chapter 1, Configuring Routing Policy.

You can press Ctrl+c to interrupt the show command output.

NOTE: The router does not recognize beginning spaces of the text string. For example, if you enter the include option with IP as the text string on which to filter, the router ignores the space and displays lines that include words such as RIP.

Example

In the following example, the output display consists only of lines that contain the string ip. The router omits all other lines of the output from the display because none of them contain the string ip.

host1#show config include-defaults | include ip

! Configuration script generated on FRI NOV 12 1999 16:56:41 UTC

ip address 192.168.1.229 255.255.255.0

ip rip receive version 2 1

ip rip send version 1

ip rip authentication mode md5 17

ip rip authentication key

ip route 10.6.0.0 255.255.0.0 192.168.1.1

ip route 10.10.0.0 255.255.0.0 192.168.1.1

ip route 10.10.0.166 255.255.255.255 192.168.1.1

ip debounce-time 0

router rip

Interface Types and Specifiers

Many commands take the variables interfaceType and interfaceSpecifier. Some commands support all types of interfaces, whereas other commands support only certain types of interfaces. Similarly, some commands support all interface specifier formats for a particular interface type, whereas other commands support only certain interface specifier formats.

Table 3 lists the interface specifiers for each type of interface on ERX-7xx models, ERX-14xx models, and the ERX-310 router.

Table 4 lists the interface specifiers for each type of interface on the E320 router.




 Table 3:  Interface Types and Specifiers for ERX-7xx Models, ERX-14xx Models, and ERX-310 Router 

 Interface Type
 Description
 Interface Specifier
 Example 

 atm

 ATM interface or
ATM 1483 subinterface

 Refer to the individual formats listed below.


  
     ATM interface or subinterface
  

 

 To configure an ATM interface or subinterface:
 slot/port[.subinterface ]

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router)
   port—Port number on the I/O module
   subinterface—Number of the subinterface in the range 1-2147483647


 atm 3/2.6


  
     ATM 1483 subinterface¹ 
  

 

 To display information about an ATM 1483 subinterface by using show commands:
 slot/port/vpi/vci

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router)
   port—Port number on the I/O module
   vpi—Virtual path identifier of the PVC on this ATM 1483 subinterface; allowable numeric range depends on the module capabilities and current configuration
   vci—Virtual circuit identifier of the PVC on this ATM 1483 subinterface; allowable numeric range depends on the module capabilities and current configuration


 atm 3/2/1/2 


 fastEthernet

 IEEE 802.3 Fast Ethernet (FE) interface

 slot/port[.subinterface1[.subinterface2 ] ]

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router)
   port—Port number on the I/O module or port 0 for the Fast Ethernet management port on the SRP I/O module 

 The meaning of the subinterface variables depends on the configuration context. You can configure Fast Ethernet interfaces with or without VLANS.

   VLANs:

  
     subinterface1—Number of the VLAN subinterface in the range 1-2147483647; no more than 4096 VLAN subinterfaces per Fast Ethernet physical port
     subinterface2—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per Fast Ethernet physical port
  

   No VLANs:

  
     subinterface1—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per Fast Ethernet physical port
     subinterface2—Not used
  

 fastEthernet 3/2.6.20


 gigabitEthernet

 IEEE 802.3 Gigabit Ethernet (GE) interface

 slot/port[.subinterface1[.subinterface2 ] ]

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router)
   port—Port number on the I/O module

 The meaning of the subinterface variables depends on the configuration context. You can configure Gigabit Ethernet interfaces with or without VLANs. 

   VLANs:

  
     subinterface1—Number of the VLAN subinterface in the range 1-2147483647; no more than 4096 VLAN subinterfaces per Gigabit Ethernet physical port
     subinterface2—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per Gigabit Ethernet physical port
  

   No VLANs:

  
     subinterface1—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per Gigabit Ethernet physical port
     subinterface2—Not used
  

 gigabitEthernet 3/0.6.20 


 hssi 

 High-speed serial interface

 slot/port[.subinterface ]

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models) and 0-13 (ERX-14xx models)
   port—Port number on the I/O module
   subinterface—Number of the subinterface in the range 1-2147483647²


 hssi 3/0


 lag 

 IEEE 802.3ad link aggregation group (LAG) interface

 bundle-name[.subinterface ]

   bundle-name—Name of the bundle
   subinterface—Number of the LAG subinterface in the range 1-2147483647


 lag paris.2


 loopback

 Loopback interface

 integer

   integer—Integer in the range
1-4294967293


 loopback 20


 mlframe-relay

 Multilink frame relay interface

 bundle-name[.subinterface ]

   bundle-name—Name of the bundle
   subinterface—Number of the MLFR subinterface in the range 1-4294967293


 mlframe-relay boston.1


 mlppp

 Multilink PPP interface

 bundle-name

   bundle-name—Name of the bundle


 mlppp chicago


 null³

 Null interface, which cannot forward or receive traffic

 0

 null 0


 pos 

 Packet over SONET (POS) interface

 slot/port[.subinterface ]

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router)
   port—Port number on the I/O module
   subinterface—Number of the subinterface in the range 1-2147483647^c


 pos 3/2


 serial

 CE1, CT1, CT3, E3-FRAME, T3-FRAME, cOCx/STMx interface, or X.21/V.35 interface

 Refer to the individual formats listed below.


  
     CE1/CT1
  

 

 slot/port:channel-group[.subinterface ]

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models) and 0-13 (ERX-14xx models)
   port—Port number on the I/O module
   channel-group—Number of the channel group associated with a range of DS0 timeslots on a CE1 or CT1 module; in the range 1-31 for a CE1 module, and 1-24 for a CT1 module
   subinterface—Number of the subinterface in the range 1-2147483647^c


 serial 3/2:20


  
     CT3
  

 

 slot/port:channel/subchannel[.subinterface ]

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models) and 0-13 (ERX-14xx models)
   port—Port number on the I/O module
   channel—Number of a T1 channel on a CT3 module; in the range 1-28
   subchannel—Number of the channel group associated with a range of DS0 timeslots on a CT3 module; in the range 1-28
   subinterface—Number of the subinterface in the range 1-2147483647^c


 serial 3/2:20/15


  
     E3/T3 FRAME
  

 

 slot/port[.subinterface ]

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models) and 0-13 (ERX-14xx models)
   port—Port number on the I/O module
   subinterface—Number of the subinterface in the range 1-2147483647^c


 serial 3/2


  
     cOCx/STMx:
unframed E1
  

 

 slot/port:path-channel/path-payload/
tributary-group/tributary-number/
channelNumber[.subinterface ]

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router)
   port—Port number on the I/O module
   path-channel—Number of the STS-1or STM-0 line in the range 1-2147483648 
   path-payload—Number of the payload within the path
   tributary-group—Number of the tributary group within the path
   tributary-number—Number of the tributary within the group
   channelNumber—1 (the router assigns the number one to an unframed E1 channel)
   subinterface—Number of the subinterface in the range 1-2147483647^c


 serial 3/0:10/1/2/2/1


  
     cOCx/STMx: fractional E1/T1
  

 

 slot/port:path-channel/path-payload/
tributary-group/tributary-number/
channel-group[.subinterface ]

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router)
   port—Port number on the I/O module
   path-channel—Number of the STS-1or STM-0 line in the range 1-2147483648
   path-payload—Number of the payload within the path
   tributary-group—Number of the tributary group within the path
   tributary-number—Number of the tributary within the group
   channel-group—Number of a fractional T1 or E1 line
   subinterface—Number of the subinterface in the range 1-2147483647^c


 serial 3/0:10/1/2/2/1


  
     cOCx/STMx: unchannelized DS3
  

 

 slot/port:path-channel/ds3-channel-number
[.subinterface ]

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router)
   port—Port number on the I/O module
   path-channel—Number of the STS-1or STM-0 line in the range 1-2147483648 
   ds3-channel-number—Number of a T3 channel
   subinterface—Number of the subinterface in the range 1-2147483647^c


 serial 3/0:1/1


  
     cOCx/STMx: DS3 channelized to DS0
  

 

 slot/port:path-channel/ds3-channel-number/
ds1-channel-number/subchannel-number
[.subinterface ]

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router)
   port—Port number on the I/O module
   path-channel—Number of the STS-1or STM-0 line in the range 1-2147483648 
   ds3-channel-number—Number of a T3 channel
   ds1-channel-number—Number of a T1 channel
   subchannel-number—Number of a fractional T1 channel
   subinterface—Number of the subinterface in the range 1-2147483647^c


 serial 3/0:1/1/10/15


  
     X.21/V.35
  

 

 slot/port[.subinterface ]

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models) and 0-13 (ERX-14xx models)
   port—Port number on the I/O module
   subinterface—Number of the subinterface in the range 1-2147483647^c


 serial 3/1


 sonet - line layer

 Line layer of a SONET/SDH interface

 slot/port

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router)
   port—Port number on the I/O module


 sonet 3/0


 sonet - path layer

 Path layer of a SONET/SDH interface

 slot/port:path-channel

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router)
   port—Port number on the I/O module
   path-channel—Number of the STS-1or STM-0 line in the range 1-2147483648 


 sonet 3/0:2


 sonet - section layer

 Section layer of a SONET/SDH interface

 slot/port

   slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router)
   port—Port number on the I/O module


 sonet 3/0


 tunnel 

 Tunnel interface 

 tunnel-type:tunnel-name[.subinterface ]

   tunnel-type—Type of the tunnel: dvmrp, gre, ipsec, l2tp, or mpls
   tunnel-name—Name of the tunnel
   subinterface—For GRE tunnels, number of the subinterface in the range 1-2147483647^c


 tunnel gre:boston





  Footnote: ¹You can use the atm slot/port/vpi/vci interface specifier format as an alternative to the atm slot/port.subinterface format with the specific show interface and show subinterface commands to monitor all ATM 1483 subinterfaces (except NBMA interfaces) as well as the upper-layer interfaces configured over an ATM 1483 subinterface. You cannot, however, use the atm slot/port/vpi/vci format to create or modify an ATM 1483 subinterface.
  Footnote: ²See JUNOSe Link Layer Configuration Guide, Chapter 2, Configuring Frame Relay for details on specifying Frame Relay subinterfaces.
  Footnote: ³You cannot configure values on the null interface. This interface acts as a data sink; it cannot forward or receive traffic.

Interface Type	Description	Interface Specifier	Example
atm	ATM interface or ATM 1483 subinterface	Refer to the individual formats listed below.
ATM interface or subinterface		To configure an ATM interface or subinterface: slot/port[.subinterface ] slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router) port—Port number on the I/O module subinterface—Number of the subinterface in the range 1-2147483647	atm 3/2.6
ATM 1483 subinterface¹		To display information about an ATM 1483 subinterface by using show commands: slot/port/vpi/vci slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router) port—Port number on the I/O module vpi—Virtual path identifier of the PVC on this ATM 1483 subinterface; allowable numeric range depends on the module capabilities and current configuration vci—Virtual circuit identifier of the PVC on this ATM 1483 subinterface; allowable numeric range depends on the module capabilities and current configuration	atm 3/2/1/2
fastEthernet	IEEE 802.3 Fast Ethernet (FE) interface	slot/port[.subinterface1[.subinterface2 ] ] slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router) port—Port number on the I/O module or port 0 for the Fast Ethernet management port on the SRP I/O module The meaning of the subinterface variables depends on the configuration context. You can configure Fast Ethernet interfaces with or without VLANS. VLANs: subinterface1—Number of the VLAN subinterface in the range 1-2147483647; no more than 4096 VLAN subinterfaces per Fast Ethernet physical port subinterface2—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per Fast Ethernet physical port No VLANs: subinterface1—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per Fast Ethernet physical port subinterface2—Not used	fastEthernet 3/2.6.20
gigabitEthernet	IEEE 802.3 Gigabit Ethernet (GE) interface	slot/port[.subinterface1[.subinterface2 ] ] slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router) port—Port number on the I/O module The meaning of the subinterface variables depends on the configuration context. You can configure Gigabit Ethernet interfaces with or without VLANs. VLANs: subinterface1—Number of the VLAN subinterface in the range 1-2147483647; no more than 4096 VLAN subinterfaces per Gigabit Ethernet physical port subinterface2—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per Gigabit Ethernet physical port No VLANs: subinterface1—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per Gigabit Ethernet physical port subinterface2—Not used	gigabitEthernet 3/0.6.20
hssi	High-speed serial interface	slot/port[.subinterface ] slot—Number of the chassis slot in the range 0-6 (ERX-7xx models) and 0-13 (ERX-14xx models) port—Port number on the I/O module subinterface—Number of the subinterface in the range 1-2147483647²	hssi 3/0
lag	IEEE 802.3ad link aggregation group (LAG) interface	bundle-name[.subinterface ] bundle-name—Name of the bundle subinterface—Number of the LAG subinterface in the range 1-2147483647	lag paris.2
loopback	Loopback interface	integer integer—Integer in the range 1-4294967293	loopback 20
mlframe-relay	Multilink frame relay interface	bundle-name[.subinterface ] bundle-name—Name of the bundle subinterface—Number of the MLFR subinterface in the range 1-4294967293	mlframe-relay boston.1
mlppp	Multilink PPP interface	bundle-name bundle-name—Name of the bundle	mlppp chicago
null³	Null interface, which cannot forward or receive traffic	0	null 0
pos	Packet over SONET (POS) interface	slot/port[.subinterface ] slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router) port—Port number on the I/O module subinterface—Number of the subinterface in the range 1-2147483647^c	pos 3/2
serial	CE1, CT1, CT3, E3-FRAME, T3-FRAME, cOCx/STMx interface, or X.21/V.35 interface	Refer to the individual formats listed below.
CE1/CT1		slot/port:channel-group[.subinterface ] slot—Number of the chassis slot in the range 0-6 (ERX-7xx models) and 0-13 (ERX-14xx models) port—Port number on the I/O module channel-group—Number of the channel group associated with a range of DS0 timeslots on a CE1 or CT1 module; in the range 1-31 for a CE1 module, and 1-24 for a CT1 module subinterface—Number of the subinterface in the range 1-2147483647^c	serial 3/2:20
CT3		slot/port:channel/subchannel[.subinterface ] slot—Number of the chassis slot in the range 0-6 (ERX-7xx models) and 0-13 (ERX-14xx models) port—Port number on the I/O module channel—Number of a T1 channel on a CT3 module; in the range 1-28 subchannel—Number of the channel group associated with a range of DS0 timeslots on a CT3 module; in the range 1-28 subinterface—Number of the subinterface in the range 1-2147483647^c	serial 3/2:20/15
E3/T3 FRAME		slot/port[.subinterface ] slot—Number of the chassis slot in the range 0-6 (ERX-7xx models) and 0-13 (ERX-14xx models) port—Port number on the I/O module subinterface—Number of the subinterface in the range 1-2147483647^c	serial 3/2
cOCx/STMx: unframed E1		slot/port:path-channel/path-payload/ tributary-group/tributary-number/ channelNumber[.subinterface ] slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router) port—Port number on the I/O module path-channel—Number of the STS-1or STM-0 line in the range 1-2147483648 path-payload—Number of the payload within the path tributary-group—Number of the tributary group within the path tributary-number—Number of the tributary within the group channelNumber—1 (the router assigns the number one to an unframed E1 channel) subinterface—Number of the subinterface in the range 1-2147483647^c	serial 3/0:10/1/2/2/1
cOCx/STMx: fractional E1/T1		slot/port:path-channel/path-payload/ tributary-group/tributary-number/ channel-group[.subinterface ] slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router) port—Port number on the I/O module path-channel—Number of the STS-1or STM-0 line in the range 1-2147483648 path-payload—Number of the payload within the path tributary-group—Number of the tributary group within the path tributary-number—Number of the tributary within the group channel-group—Number of a fractional T1 or E1 line subinterface—Number of the subinterface in the range 1-2147483647^c	serial 3/0:10/1/2/2/1
cOCx/STMx: unchannelized DS3		slot/port:path-channel/ds3-channel-number [.subinterface ] slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router) port—Port number on the I/O module path-channel—Number of the STS-1or STM-0 line in the range 1-2147483648 ds3-channel-number—Number of a T3 channel subinterface—Number of the subinterface in the range 1-2147483647^c	serial 3/0:1/1
cOCx/STMx: DS3 channelized to DS0		slot/port:path-channel/ds3-channel-number/ ds1-channel-number/subchannel-number [.subinterface ] slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router) port—Port number on the I/O module path-channel—Number of the STS-1or STM-0 line in the range 1-2147483648 ds3-channel-number—Number of a T3 channel ds1-channel-number—Number of a T1 channel subchannel-number—Number of a fractional T1 channel subinterface—Number of the subinterface in the range 1-2147483647^c	serial 3/0:1/1/10/15
X.21/V.35		slot/port[.subinterface ] slot—Number of the chassis slot in the range 0-6 (ERX-7xx models) and 0-13 (ERX-14xx models) port—Port number on the I/O module subinterface—Number of the subinterface in the range 1-2147483647^c	serial 3/1
sonet - line layer	Line layer of a SONET/SDH interface	slot/port slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router) port—Port number on the I/O module	sonet 3/0
sonet - path layer	Path layer of a SONET/SDH interface	slot/port:path-channel slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router) port—Port number on the I/O module path-channel—Number of the STS-1or STM-0 line in the range 1-2147483648	sonet 3/0:2
sonet - section layer	Section layer of a SONET/SDH interface	slot/port slot—Number of the chassis slot in the range 0-6 (ERX-7xx models), 0-13 (ERX-14xx models), and 0-2 (ERX-310 router) port—Port number on the I/O module	sonet 3/0
tunnel	Tunnel interface	tunnel-type:tunnel-name[.subinterface ] tunnel-type—Type of the tunnel: dvmrp, gre, ipsec, l2tp, or mpls tunnel-name—Name of the tunnel subinterface—For GRE tunnels, number of the subinterface in the range 1-2147483647^c	tunnel gre:boston




 Table 4:  Interface Types and Specifiers for E320 Router 

 Interface Type
 Description
 Interface Specifier
 Example 

 atm

 ATM interface or
ATM 1483 subinterface

 Refer to the individual formats listed below.


  
     ATM interface or subinterface

  

 

 To configure an ATM interface or subinterface:
 slot/adapter/port[.subinterface ]

   slot—Number of the chassis slot in the range 0-5 or 11-16
   adapter—Identifier for the IOA within the chassis slot, either 0 or 1, where:

  
     0 indicates that the IOA is installed in the upper IOA bay.
     1 indicates that the IOA is installed in the lower IOA bay.
  

   port—Port number on the IOA
   subinterface—Number of the subinterface in the range 1-2147483647


 atm 3/1/7.6


  
     ATM 1483 subinterface¹ 
  

 

 To display information about an ATM 1483 subinterface by using show commands:
 slot/adapter/port/vpi/vci

   slot—Number of the chassis slot in the range 0-5 or 11-16
   adapter—Identifier for the IOA within the chassis slot, either 0 or 1, where:

  
     0 indicates that the IOA is installed in the upper IOA bay.
     1 indicates that the IOA is installed in the lower IOA bay.
  

   port—Port number on the IOA
   vpi—Virtual path identifier of the PVC on this ATM 1483 subinterface; numeric range for the E320 router is 0-255
   vci—Virtual circuit identifier of the PVC on this ATM 1483 subinterface; numeric range for the E320 router is 1-65535 


 atm 3/1/7/1/2 


 fastEthernet
 (for Fast Ethernet management port on SRP IOA)
 

 IEEE 802.3 Fast Ethernet (FE) interface

 slot/adapter/port

   slot—Number of the chassis slot, either 6 or 7
   adapter—Identifier for the SRP I/O adapter (IOA) within the chassis slot; always 0
   port—Port number on the SRP IOA; always 0


 fastEthernet 6/0/0


 gigabitEthernet
 

 IEEE 802.3 Gigabit Ethernet (GE) interface

 slot/adapter/port[.subinterface1[.subinterface2 ] ]

   slot—Number of the chassis slot in the range 0-5 or 11-16
   adapter—Identifier for the IOA within the chassis slot, either 0 or 1, where:

  
     0 indicates that the IOA is installed in the upper IOA bay.
     1 indicates that the IOA is installed in the lower IOA bay. 
  

   port—Port number on the IOA

 The meaning of the subinterface variables depends on the configuration context. You can configure Gigabit Ethernet interfaces with or without VLANs. 

   VLANs:

  
     subinterface1—Number of the VLAN subinterface in the range 1-2147483647; no more than 4096 VLAN subinterfaces per Gigabit Ethernet physical port
     subinterface2—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per Gigabit Ethernet physical port
  

   No VLANs:

  
     subinterface1—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per Gigabit Ethernet physical port
     subinterface2—Not used
  

 gigabitEthernet 4/0/1.20


 lag 

 IEEE 802.3ad link aggregation group (LAG) interface

 bundle-name[.subinterface ]

   bundle-name—Name of the bundle
   subinterface—Number of the LAG subinterface in the range 1-2147483647


 lag paris.2


 pos
 

 Packet over SONET (POS) interface

 slot/adapter/port

   slot—Number of the chassis slot in the range 0-5 or 11-16
   adapter—Identifier for the IOA within the chassis slot, either 0 or 1, where:

  
     0 indicates that the IOA is installed in the upper IOA bay.
     1 indicates that the IOA is installed in the lower IOA bay. 
  

   port—Port number on the IOA


 pos 5/0/0


 sonet - line layer
 

 Line layer of a SONET/SDH interface

 slot/adapter/port

   slot—Number of the chassis slot in the range 0-5 or 11-16
   adapter—Identifier for the IOA within the chassis slot, either 0 or 1, where:

  
     0 indicates that the IOA is installed in the upper IOA bay.
     1 indicates that the IOA is installed in the lower IOA bay. 
  

   port—Port number on the IOA


 sonet 3/0/0


 sonet - path layer
 

 Path layer of a SONET/SDH interface

 slot/adapter/port

   slot—Number of the chassis slot in the range 0-5 or 11-16
   adapter—Identifier for the IOA within the chassis slot, either 0 or 1, where:

  
     0 indicates that the IOA is installed in the upper IOA bay.
     1 indicates that the IOA is installed in the lower IOA bay. 
  

   port—Port number on the IOA


 sonet 3/0/0


 sonet - section layer
 

 Section layer of a SONET/SDH interface

 slot/adapter/port

   slot—Number of the chassis slot in the range 0-5 or 11-16
   adapter—Identifier for the IOA within the chassis slot, either 0 or 1, where:

  
     0 indicates that the IOA is installed in the upper IOA bay.
     1 indicates that the IOA is installed in the lower IOA bay. 
  

   port—Port number on the IOA


 sonet 3/0/0


 tenGigabitEthernet
 

 IEEE 802.3ae 10-Gigabit Ethernet (GE) interface

 slot/adapter/port[.subinterface1[.subinterface2 ] ]

   slot—Number of the chassis slot in the range 0-5 or 11-16
   adapter—Identifier for the IOA within the chassis slot. 0 indicates that this a full-height IOA.
   port—Port number on the IOA

 The meaning of the subinterface variables depends on the configuration context. You can configure 10-Gigabit Ethernet interfaces with or without VLANs. 

   VLANs:

  
     subinterface1—Number of the VLAN subinterface in the range 1-2147483647; no more than 4096 VLAN subinterfaces per 10-Gigabit Ethernet physical port
     subinterface2—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per 10-Gigabit Ethernet physical port
  

   No VLANs:

  
     subinterface1—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per 10-Gigabit Ethernet physical port
     subinterface2—Not used
  

 tenGigabitEthernet 4/0/1.20


 tunnel
 

 Tunnel interface

 tunnel-type:tunnel-name[.subinterface]

   tunnel-type—Type of the tunnel: dvmrp, gre,  l2tp, or mpls 
   tunnel-name—Name of the tunnel
   subinterface—For GRE tunnels, number of the subinterface in the range 1-2147483647^²


 tunnel gre:boston





  Footnote: ¹You can use the atm slot/adapter/port/vpi/vci interface specifier format as an alternative to the atm slot/adapter/port.subinterface format with the specific show interface and show subinterface commands to monitor all ATM 1483 subinterfaces (except NBMA interfaces) as well as the upper-layer interfaces configured over an ATM 1483 subinterface. You cannot, however, use the atm slot/adapter/port/vpi/vci format to create or modify an ATM 1483 subinterface. 
  Footnote: ²You cannot configure values on the null interface. This interface acts as a data sink; it cannot forward or receive traffic.

Interface Type	Description	Interface Specifier	Example
atm	ATM interface or ATM 1483 subinterface	Refer to the individual formats listed below.
ATM interface or subinterface		To configure an ATM interface or subinterface: slot/adapter/port[.subinterface ] slot—Number of the chassis slot in the range 0-5 or 11-16 adapter—Identifier for the IOA within the chassis slot, either 0 or 1, where: 0 indicates that the IOA is installed in the upper IOA bay. 1 indicates that the IOA is installed in the lower IOA bay. port—Port number on the IOA subinterface—Number of the subinterface in the range 1-2147483647	atm 3/1/7.6
ATM 1483 subinterface¹		To display information about an ATM 1483 subinterface by using show commands: slot/adapter/port/vpi/vci slot—Number of the chassis slot in the range 0-5 or 11-16 adapter—Identifier for the IOA within the chassis slot, either 0 or 1, where: 0 indicates that the IOA is installed in the upper IOA bay. 1 indicates that the IOA is installed in the lower IOA bay. port—Port number on the IOA vpi—Virtual path identifier of the PVC on this ATM 1483 subinterface; numeric range for the E320 router is 0-255 vci—Virtual circuit identifier of the PVC on this ATM 1483 subinterface; numeric range for the E320 router is 1-65535	atm 3/1/7/1/2
fastEthernet (for Fast Ethernet management port on SRP IOA)	IEEE 802.3 Fast Ethernet (FE) interface	slot/adapter/port slot—Number of the chassis slot, either 6 or 7 adapter—Identifier for the SRP I/O adapter (IOA) within the chassis slot; always 0 port—Port number on the SRP IOA; always 0	fastEthernet 6/0/0
gigabitEthernet	IEEE 802.3 Gigabit Ethernet (GE) interface	slot/adapter/port[.subinterface1[.subinterface2 ] ] slot—Number of the chassis slot in the range 0-5 or 11-16 adapter—Identifier for the IOA within the chassis slot, either 0 or 1, where: 0 indicates that the IOA is installed in the upper IOA bay. 1 indicates that the IOA is installed in the lower IOA bay. port—Port number on the IOA The meaning of the subinterface variables depends on the configuration context. You can configure Gigabit Ethernet interfaces with or without VLANs. VLANs: subinterface1—Number of the VLAN subinterface in the range 1-2147483647; no more than 4096 VLAN subinterfaces per Gigabit Ethernet physical port subinterface2—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per Gigabit Ethernet physical port No VLANs: subinterface1—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per Gigabit Ethernet physical port subinterface2—Not used	gigabitEthernet 4/0/1.20
lag	IEEE 802.3ad link aggregation group (LAG) interface	bundle-name[.subinterface ] bundle-name—Name of the bundle subinterface—Number of the LAG subinterface in the range 1-2147483647	lag paris.2
pos	Packet over SONET (POS) interface	slot/adapter/port slot—Number of the chassis slot in the range 0-5 or 11-16 adapter—Identifier for the IOA within the chassis slot, either 0 or 1, where: 0 indicates that the IOA is installed in the upper IOA bay. 1 indicates that the IOA is installed in the lower IOA bay. port—Port number on the IOA	pos 5/0/0
sonet - line layer	Line layer of a SONET/SDH interface	slot/adapter/port slot—Number of the chassis slot in the range 0-5 or 11-16 adapter—Identifier for the IOA within the chassis slot, either 0 or 1, where: 0 indicates that the IOA is installed in the upper IOA bay. 1 indicates that the IOA is installed in the lower IOA bay. port—Port number on the IOA	sonet 3/0/0
sonet - path layer	Path layer of a SONET/SDH interface	slot/adapter/port slot—Number of the chassis slot in the range 0-5 or 11-16 adapter—Identifier for the IOA within the chassis slot, either 0 or 1, where: 0 indicates that the IOA is installed in the upper IOA bay. 1 indicates that the IOA is installed in the lower IOA bay. port—Port number on the IOA	sonet 3/0/0
sonet - section layer	Section layer of a SONET/SDH interface	slot/adapter/port slot—Number of the chassis slot in the range 0-5 or 11-16 adapter—Identifier for the IOA within the chassis slot, either 0 or 1, where: 0 indicates that the IOA is installed in the upper IOA bay. 1 indicates that the IOA is installed in the lower IOA bay. port—Port number on the IOA	sonet 3/0/0
tenGigabitEthernet	IEEE 802.3ae 10-Gigabit Ethernet (GE) interface	slot/adapter/port[.subinterface1[.subinterface2 ] ] slot—Number of the chassis slot in the range 0-5 or 11-16 adapter—Identifier for the IOA within the chassis slot. 0 indicates that this a full-height IOA. port—Port number on the IOA The meaning of the subinterface variables depends on the configuration context. You can configure 10-Gigabit Ethernet interfaces with or without VLANs. VLANs: subinterface1—Number of the VLAN subinterface in the range 1-2147483647; no more than 4096 VLAN subinterfaces per 10-Gigabit Ethernet physical port subinterface2—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per 10-Gigabit Ethernet physical port No VLANs: subinterface1—When using PPPoE, the number of the PPPoE subinterface in the range 1-2147483647; no more than 4094 PPPoE subinterfaces per 10-Gigabit Ethernet physical port subinterface2—Not used	tenGigabitEthernet 4/0/1.20
tunnel	Tunnel interface	tunnel-type:tunnel-name[.subinterface] tunnel-type—Type of the tunnel: dvmrp, gre, l2tp, or mpls tunnel-name—Name of the tunnel subinterface—For GRE tunnels, number of the subinterface in the range 1-2147483647^²	tunnel gre:boston

[Contents] [Prev] [Next] [Index] [Cisco] [Reload]